delabs (Page 10)

Product Design - Industrial Automation and Instrumentation. -

Here is a 4-20 mA In/Out Analog Mux with Cascade option. This is a simple circuit i designed to make a Automation System within a budget.

Mixed Circuits Analog with Digital

Analog Mux using 4051

This takes 4-20mA from many Transmitters and gives out just one 4-20 mA output. The Mux is done with a digital byte or word. This is a slow scanner as process is slow, that way many analog inputs can be multiplexed and sent into one analog input of a D/A. In near real time systems a faster mux could be used or mux totally avoided. This was made in some numbers, so the pcb is better than others.

4-20mA Multiplexer Circuit – pdf

This circuit is a small representation of a very low cost printer sharer. It has no Active Devices only diodes.

Simple High speed data switch

Pot the product in epoxy with a black dye, they serve the purpose. Output impedance of this circuit is high, sink is 220K source is 3.9K+ so use some buffers or drivers at Output. If Buffers are omitted, then fix this unit on the printer port connector of Computer.

when Enable A is at float-high impedance or low the output O1-O4 is not influenced by A1-A4 inputs. If Enable A is made logic high or 5V then A1-A4 is available at O1-O4.

By turning Enable A or Enable B high, you can route the data A1-A4 or B1-B4 to the output O1-O4, you can also mix data and you can expand to any number of input sets or data width. 1N4148 is fast, 4nS, that makes this data switch quite fast. This circuit cannot drive long printer cables without drivers. They will load the output.

A Power Transistor which is having a drop of 4 Volts across it and passing 3 amps thru it, may dissipate around 12 Watts of Heat, This is the problem in Series Regulators. While a Saturated Transistor or Mosfet with 1 Volts across and 3 Amps Thru will be just 3 Watts. But then a fully on transistor or mosfet cannot be controlled or regulated, for that we turn it ON and OFF very fast so that the right amount of current or voltage is delivered.

Power Electronic Circuits  

5V -1A Power Supply using LM2575

The way this is done is PWM – Pulse Width Modulation. In this the mosfet or transistor is switched ON-OFF at say 100 kHz, but the ON duration is varied to control the output. The longer the duration of ON time more energy or punch is transferred. Switching losses will be present depending on how fast the rise and fall times of the pulses are.

The Pulsed AC or Chopped DC can be smoothed to the Average with Inductors and Capacitors. The reactive pulses of the Inductor has to be absorbed by a Schottky Rectifier 1N5817 — 20V-1A fast switching diode with low switching losses.

This circuit is derived from an application note of LM2575, It is a Power Switching Regulator from National Semiconductor The details are here LM2575

This is the standard configuration on how to Interface a uC like 8051 to PC RS232 with MAX232A. The UART or Serial port was not present in 8049/8749 chips which were the ancestors of 8051/8031. Pages of code were needed to make a software UART in MCS-48. The 8051 integrated the hardware UART and short commands made it tick. The most important innovation which made uC popular was the C in 80C31. C is for CMOS. This made the chip work cooler and work on even batteries and small power supplies.

80C51, SBC, Firmware and Circuits

The 8749 and 8751 are the UV EPROM type of uC. With limited erase/write cycles. The FLASH revolution changed every thing, you could update firmware over a phone line modem. Even without Ethernet, the firmware could be updated by making every embedded device a node on the EPABX. Now TCP/IP and Wi-Fi makes it all very easy.

Interface a uC to PC RS232 with MAX232A
Read also –

A sample and hold is like an analog memory. If The digital control A is low 4066 switch is open, and when A is high switch is closed. U2B is a buffer so as to ensure quick charging of C1 thru 4066 on resistance of 100E.

Simple Sample and Hold with CD4066

Mixed and Interface Circuits

U2A is a FET input opamp buffer which does not load or drain the cap C1. When A goes high the input analog sample is stored in C1. A has to be high for say 10*1uF*100E = 1mS, so that a proper stable sample is stored. When A is low C1 undergoes very slow discharge as opamp input resistance and 4066 off resistance is in giga ohms. The accuracy of reading Vout falls with respect to time due to leakage currents.

The Edsion Filament lamp may be less popular, but it is the most cost-effective light even today. It is very affordable, The light is soothing to the eyes and best of all gives a warm feeling.

Edison Bulb Life Extender

Sometimes due to the mains being restored when bulb is on, or a rapid flick of switch, blows it. This may be due to the cold filament resistance which is low, allowing a huge inrush current.

LED Lighting – The Future is Here

The problem can be solved with a soft start based on thyristor or mosfet using PWM etc. The circuit here is a low cost solution which may help a bit in reducing the inrush cold current Protection from long duration high voltages is also required but will make circuit more complex.

Now why would anyone spend for a R-C network for a bulb, you could as well buy a new bulb. But I once got a back sprain while replacing a bulb in a hurry, So the price of the bulb alone is not the issue.

CFL Lamps and Simple Inverter

The two diodes 1A form a AC path with a switching delay of diodes, The R-C network is for soft start. The Varistor-Thermistor has a cold resistance 4.7E which reduces as it warms up. If switch is flicked rapidly or power fluctuates, then varistor cannot help as its response is slow. The 10E resistor ceramic fusible wirewound resistor and C1 does the job of absorbing .

This circuit has not been tested for long times at multiple places, so i am not sure of its performance.

This indicates like LM3914 in dot-mode. It is a drawing i made made to troubleshoot a gadget, around two decades ago. Strangely it had a echo of a design i had made into a 7107 dpm years before that. Now i am scanning all my drawing and notes, useful or not. Clean or with errors. Many Errors = 1 Blunder. Some projects i made have been expensive Blunders. So see them with a skeptic eye, fix them, try them. Thats all for now.

See the Circuit Full Size – Microohm Meter with LED Analog Bar

Microohm Meter with LED Analog Bar

This has a 9V battery power. The 555 spins and a negative voltage for Opamp is created. This is a Low Offset amp of OP37 of Precision Monolithics, Inc PMI an early innovator. This diff-amp amplifies the uV of a 4 wire resistance measurement.

Now the current pump is the 2N2222 you see above the OP37. The FET and 555 do synchronous rectification. The LM324 is the Indicator and Analog to LED Dot-Bar Converter. The probes are Gold Plated, or use solid gold pins if you have them in plenty.